How to choose the right canopy size for a robotic lawn mower
Properly selected dimensions of a robotic lawn mower cover must take into account not only the docking station itself, but also the approach path, cover height, and clearance from lawn edges.
A robot does not need a tight "garage." If the canopy is to work well in practice, it must protect the station while also leaving enough room for approach and smooth docking. That is why, when choosing a robotic lawn mower cover by dimensions, you need to look beyond just the length and width of the machine itself.
In this article, we focus exclusively on dimensions: how to measure the installation spot, how much side clearance to leave, how much space is needed above the station, and how far the canopy should be set back from the lawn edge. We have covered the general purpose of protective covers elsewhere; here, the key things are numbers and practical installation considerations.
How to measure the space for a robotic lawn mower cover by dimensions
The starting point is not the robot alone, but the full setup: the robot, the docking station, the power cable, and the approach path. In many gardens, it is the geometry of the approach to the station that determines whether the canopy will be convenient or whether it will start interfering with everyday parking.
Before choosing a cover, it is worth measuring 4 things:
- the width of the station at its widest point,
- the depth of the station including rear clearance for the cable and plug,
- the height of the robot when positioned on the station,
- the length of the straight approach in front of the station.
For most residential robotic lawn mowers, the approximate dimensions look similar:
| Element | Typical range |
|---|---:|
| Robot width | 40–55 cm |
| Robot length | 55–75 cm |
| Robot height | 23–33 cm |
| Station width | 45–65 cm |
| Station depth | 70–95 cm |
These are approximate values. Small robots for lawns of 300–600 m² usually fall near the lower end, while larger models for plots of 1000–3000 m² often come close to the upper values. If the manufacturer lists the dimensions of the robot and station separately, always choose the cover based on the larger footprint of the station, not the machine alone.
Dimensions of popular models: how much space a robot with its station takes up
Differences between brands are not huge, but they are enough for a "tight-fit" canopy to turn out too small. For clarity, you can assume three device groups:
1. Small robots for simple gardens
Most commonly:
- robot width of 40–45 cm,
- length of 55–60 cm,
- height of 23–26 cm,
- station width of about 45–50 cm and depth of 70–80 cm.
For this group, a sensible minimum internal canopy size is usually around:
- 60–70 cm wide,
- 90–110 cm deep,
- 45–55 cm high.
2. Medium robots for gardens of 600–1500 m²
Most commonly:
- robot width of 45–50 cm,
- length of 60–65 cm,
- height of 25–30 cm,
- station width of 50–60 cm, depth of 80–90 cm.
Here, it is worth aiming for a canopy with an internal clearance of about:
- 70–80 cm in width,
- 100–120 cm in depth,
- 50–60 cm in height.
3. Larger robots for big lawns
Most commonly:
- width of 50–55 cm,
- length of 65–75 cm,
- height of 28–33 cm,
- station width of 55–65 cm, depth of 85–95 cm.
For this group, a safe starting point is:
- 80–90 cm wide,
- 110–130 cm deep,
- 55–65 cm high.
This still does not replace measuring the specific model. Some stations have a more protruding front, others require a larger approach radius, and some have a factory cover that also needs to be taken into account.
How much clearance to leave for maneuvering into the station
The most common mistake is choosing a canopy that matches the footprint of the base exactly. A robot rarely approaches perfectly along a single axis. It adjusts its path, slows down, sometimes comes in slightly from the side, and only at the last moment aligns itself centrally.
That is why it is worth assuming at least:
- 7–10 cm of clearance on each side of the station,
- at least 15–25 cm of extra space in front of the station, still under the roof,
- 40–80 cm of straight approach before the canopy, with no curb, post, or dense planting.
If the approach to the station is curved or the guide wire directs the robot at a slight angle, the side clearance should be greater. In practice, it is better to have 15 cm of free space on the sides than 5 cm. This is especially important with covers that have side walls or enclosed legs.
You also need to watch out for elements that physically narrow the entrance:
- support posts placed right at the front,
- recessed canopy sides,
- a roof front that hangs too low,
- lawn edging higher than 2–3 cm.
If the robot is to drive into the station over paving, a slab, or a stabilizing strip, the width of that strip should be greater than the width of the robot by at least 10 cm on each side. For a robot that is 45 cm wide, that gives a comfortable approach strip of about 65 cm.
What the height above the station and robot should be
The height of the canopy is not only there so the robot can fit underneath. You also need space above the station cover, antenna, sensors, and any upward opening service flap. If the canopy is too low, every maintenance task ends with removing or shifting the entire cover.
A sensible rule is simple:
- measure the highest point of the robot standing on the station,
- add at least 10 cm of free space,
- if the station has a flap or cover that opens upward, check the required service clearance.
In practice:
- for a robot that is 24 cm high, a cover with a clearance of about 40–45 cm is usually enough,
- for a robot that is 30 cm high, 50 cm is more comfortable,
- for larger models and stations with taller housings, it is safer to assume 55–65 cm.
If the roof is flat and slopes toward the rear, measure the height at the lowest point, not at the front. This is a common detail overlooked during purchase. From the outside, the canopy may appear tall, but inside the actual clearance can be several centimeters less because of the roof structure and profiles.
Clearance from the lawn edge and edging
A station placed too close to the lawn edge can cause entry problems even without a canopy. Once a cover is added, the margin for error becomes even smaller. That is why you need to leave room not only for the robot itself, but also for a straight and predictable path of movement.
The safest assumption is to keep the following distances:
- at least 10 cm from the vertical edge of the canopy to the robot's travel line,
- at least 15–20 cm from the side of the canopy to tall edging, a wall, or a palisade,
- at least 30–50 cm of free space on the sides of the canopy front, if the robot approaches on a slight curve.
If the installation spot is next to a path, terrace, or gravel strip, check the difference in levels. Even a 2–4 cm height difference can affect how the robot positions itself during docking. The canopy should not begin exactly at the boundary between grass and a hard surface if the robot then has only half a wheel on stable ground.
It is also worth remembering that some manufacturers recommend leaving specific obstacle-free zones on the sides of the station. If the manual for a particular model requires, for example, 30 cm on one side and 100 cm on the other for the guide wire, those values are more important than general assumptions.
A simple way to choose the dimensions without making mistakes
If you do not want to guess, follow this sequence of measurements and allowances:
- Measure the width and depth of the station.
- Check the height of the robot on the station.
- Add at least 7–10 cm on the sides, and preferably 10–15 cm per side.
- Add 15–25 cm at the front under the roof.
- Leave at least 10 cm of clearance above the highest point.
- Check whether you have 40–80 cm of straight approach in front of the canopy.
- Assess whether the sides of the canopy are not too close to edging, a wall, or a flower bed.
For example, if the station is 52 cm wide and 84 cm deep, and the robot reaches a height of 28 cm when on the station, the practical minimum canopy size is about:
- width: 72–82 cm,
- depth: 99–109 cm,
- height: 38 cm as an absolute minimum, but in practice 50 cm or more is better.
The second option is simply more convenient for everyday use and cleaning.
At the end, compare your measurements with the robot manufacturer's manual and the actual location in the garden. Write down the station width, the depth of the entire setup, the height of the highest point, and the length of the straight approach. Only with that complete set of data is it worth choosing a canopy, because then you know whether the problem is the size of the cover itself or the layout of the surface and edging around the station.
Design your own cover
Enter the size of your unit and see the result in the 3D preview.
Open the configurator